UTICA BOILERS UBSSC-050 Скачать руководство пользователя

Страница: 45 / 88

WARNING

If you do not follow these instructions

exactly, a fire or explosion may result causing

property damage, personal injury or loss of

life.

• This appliance is equipped with an ignition device

which automatically lights burner.

Do NOT try to

light this burner by hand.

• Before operating smell all around appliance area

for gas. Be sure to smell next to floor because

some gas is heavier than air and will settle to the

floor.

•

Use only your hand to turn the gas shutoff

valve

. Never use tools. If valve will not turn

by hand, do not try to repair it, call a qualified

service technician. Force or attempted repair may

result in fire or explosion.

• Do not use this appliance if any part has

been under water.

Immediately call a qualified

service technician to inspect appliance and to

replace any part of control system and any gas

control which has been under water.

10.1

OPERATING INSTRUCTIONS

Stop! Read Safety information above.

• Set thermostat to lowest setting.
• Turn "

OFF

" all electrical power to appliance.

• This appliance is equipped with an ignition device which

automatically lights the burner.

Do not try to light

burner by hand!

• Remove upper jacket panel.
• Turn

gas shutoff valve clockwise to closed position.

Handle should be perpendicular to gas pipe.

• Wait 5 minutes for any gas to clear. Smell for gas,

including near floor. If you smell gas,

STOP!

instructions on this page:

“What To Do If You Smell

Gas.”

If you do

not

smell gas, go to next step.

•

Turn gas shutoff valve counter clockwise to the open

position. Handle should be parallel to gas pipe.

• Replace upper jacket panel.
• Turn "

ON"

electrical power to appliance.

• Set thermostat to desired setting.
• If the appliance will not operate, follow instructions TO

TURN OFF GAS TO APPLIANCE and call your service

technician or gas supplier.

FOR YOUR SAFETY READ BEFORE OPERATING

10-1 Gas Shutoff Valve -

050/075/100/150/200 MBH

OPEN POSITION

CLOSED POSITION

CAUTION

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call the fire

department.

10.2

TO TURN OFF GAS TO APPLIANCE

• Set thermostat to lowest setting.
• Turn

"OFF"

all electric power to appliance if service is to

be performed.

• Remove front jacket panel.
•

Turn gas shutoff valve handle clockwise

to closed

position. Handle should be perpendicular to gas pipe.

• Replace front jacket panel.

Gas Shutoff

Valve

10-2 Gas Shutoff Valve - 299 MBH

10 - OPERATING INSTRUCTIONS

Gas Shutoff

Valve

PN 240011320 Rev. G 10/01/2021]

Содержание UBSSC-050

























































































Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды

UTICA BOILERS UBSSC-050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды