UTICA BOILERS UBSSC-050 страница 40 Скачать руководство пользователя

Страница: 40 / 88

9.4

Boiler Start-up and Operational Test

Verify air is purged from hydronic piping

System test pumps - verify each pump is

operational using vibration, noise and amp draw.

Verify gas piping

•

Confirm pressure test. See section 7.3.

• Visually inspect piping to determine there are no

open fittings or ends, and all valves at unused

outlets are closed and plugged/capped.

•

Purge air from piping. Confirm there is a steady

gas supply to the boiler.

• Check piping and connections for leaks

immediately after gas is turned on. Shut off gas

supply and make necessary repairs if leaks found.

Follow OPERATING INSTRUCTIONS to initiate boiler

operation. See section 10.

Inspect combustion air and vent piping. Verify pipe

is not leaking and terminations are unobstructed

and vent gas discharge is not a nuisance or hazard.

Verify boiler functions.

Inspect condensate disposal system. Verify

condensate flows adequately and is disposed

properly.

Check control module operation.

Check field sourced limits, low water cutoffs, etc.

per manufacturer's instructions.

9.5

Check Firing Rate

Measure input, if a gas meter is installed in the

system.

•

Turn off gas to all other appliances.

• Activate some heating zones to dissipate heat.
•

Set boiler on high fire.

• Use ½, 1 or 2 cu ft dial on gas meter. Measure

time required for two or more complete

revolutions. Measure time for one or more

minutes.

• Calculate input.

For Natural Gas :

Input (MBH)

3600 x cu ft
seconds

Example: Natural Gas - Gas flow from

Meter = 2 cu ft
Measured time = 72 seconds

Input Rate

(MBH)

3600 x 2 cu ft

= 100 MBH

72 seconds

9 - START UP PROCEDURE

For Propane (LP):

Input (MBH)

9160 x cu ft
seconds

Compare measured input to Table 13. If calculated

input is not in range given in Table 13, check firing

rate again after setting the combustion following

steps in section 9.6.

Table 13 - Input Rate @ High Fire (MBH)

Rate @ High Fire

Size

From

050

075

100

102

150

140

153

200

185

204

299

285

315

9.6 Combustion Adjustment

Calibrated Combustion Analyzer is necessary for the following

combustion adjustment.

Enter installer menu (Enter + Menu buttons for 4

seconds).

A. Scroll down to System Test.

B. Push Enter button to enter System Test. When

“System Test Off” displays, push Enter button and

“Off” will start flashing.

C. Scroll up to High Power and push Enter. “High Power”

will stop flashing and becomes solid.

Unit is now locked in high fire.

For Metric formulas- See Glossary

Note

Before setting combustion in HIGH fire, activate all

heating zones to dump heat generated by the boiler

running on high fire.

PN 240011320 Rev. G 10/01/2021]

Содержание UBSSC-050

























































































Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды

UTICA BOILERS UBSSC-050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды