UTICA BOILERS UBSSC-050 Скачать руководство пользователя

Страница: 35 / 88

FIGURE 7-2 Manual Main Gas Shutoff Valve Outside

Boiler Jacket

7.3

Leak Check Gas Piping

Pressure test boiler and gas connection before placing

boiler in operation.

• Pressure test over 1/2 psig (3.5 kPa). Disconnect

boiler and its individual gas shutoff valve from gas

supply system.

• Pressure test at 1/2 psig (3.5 kPa) or less. Isolate

boiler from gas supply system by closing manual

gas shutoff valve. See figure 7-2.

• Locate leakage using gas detector, noncorrosive

detection fluid, or other leak detection method

acceptable to authority having jurisdiction. Do

not use matches, candles, open flames, or other

methods that can provide ignition source.

• Correct leaks immediately and retest.

Manual Main Gas

Shutoff Valve

FIGURE 7-3 Gas Shutoff Valve - 050/075/100/150/200

DANGER

Fire Hazard. Do not use matches, candles, open

flames, or other methods providing ignition source.

Failure to comply will result in death or serious

injury.

Gas shutoff valve

(shown in closed

position)

FIGURE 7-4 Gas Shutoff Valve - 299

Gas shutoff valve

(shown in open

position)

7 - GAS SUPPLY PIPING

PN 240011320 Rev. G 10/01/2021]

Содержание UBSSC-050

























































































Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды

UTICA BOILERS UBSSC-050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды