Unitronics electric UM2B Скачать руководство пользователя страница 63

Страница: 63 / 109

5.- SOFTWARE DESCRIPTION

- 61 -

Insulation Resistance Software (ETPRA)

This screen (figure 5-42-b) shows the insulation resistance evolution referred to 20ºC.

taking into account the temperature of the transformer. The field “Temperature” should have
the value entered in “Test configuration” section while in Test phase. This field can be edited
to let the user:

- Compensate to another temperature as the user forgot entering the temperature of

the test or did not know that moment the test temperature. So entering the temperature all
the measurements would appear compensated to that value.

- Take to the screen the real measurement taken by the unit. If the user wishes the

measurement without any compensation, just have to enter the value 20 (20ºC). This way
will get the actual uncompensated temperature.

Insulation Resistance measurement is performed taking one sample each minute in 10

minutes tests and each ten seconds in 1minute last tests.

Figure 5-42-b: Analysis: Graph of insulation resistance (Insulation Resistance SW).

Содержание UM2B














































































































Результаты поиска

Содержание UM2B

Отзывы:

Похожие инструкции для UM2B

Бренды по названию

Популярные бренды

Unitronics electric UM2B, Руководство пользователя

Результаты поиска

Содержание UM2B

Отзывы:

Похожие инструкции для UM2B

Бренды по названию

Популярные бренды