Unitronics electric UM2B Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 109

background image

4.- PREPARATIONS BEFORE TO USE

- 25 -

While measuring, the cables must not be stepped, moved or hit, because
the  measurements  could  be  altered,  specially  when  measuring  high-
quality  insulations,  due  to  the  piezoelectric  effect  of  the  cable  and  the
weak  measured  currents.  If  it  is  possible,  put  these  cables  parallel  and
nearest between them to avoid interferences.

If the shell of the machine to be analyzed is grounded, a check should be

made  to  ensure  that  this  is  the  same  ground as the one of the PC supply
and the measuring unit.  To accomplish this, join these two points with a
plaited  cable  of  adequate  cross-section.

ALL THE GROUNDS USED

IN TESTING SHOULD BE INTERCONNECTED

.

- Connection of UM2B equipment to electrical mains.

This connection is accomplished by running the power cable from (5) to a
mains socket. The supply voltage should be checked to ensure that it is within
the operating limits (see chapter 9: Specifications) and a check should made
to ensure that the socket has an operative ground.

Once the different parts of the equipment have been connected, the PC should be

switched on and the control software executed. Following this, it will be sufficient to follow
the instructions as they appear on the PC screen. Consequently,

the UM2B unit should be

turned on when this software so requires

(4).

THE UM2B UNIT SHOULD NOT BE TURNED ON UNTIL
THIS IS INDICATED BY THE CONTROL SOFTWARE.

WARNING:

If the equipment is used outside manufacturer‟s

specifications, the security could be altered.

«
...
25
26
27
28
29
...
»

Содержание UM2B














































































































Отзывы:

Нет отзывов

Похожие инструкции для UM2B

Бренд: TA Страницы: 58

Бренд: X-laser Страницы: 17

Бренд: Sonel Страницы: 26

Бренд: SBS Страницы: 17

Бренд: Michell Instruments Страницы: 28

Бренд: 3nh Страницы: 39

AcuRev 1310 Series

Бренд: AccuEnergy Страницы: 109

Бренд: Agilent Technologies Страницы: 20

BAE LX-XO-PL018-L S4 Series

Бренд: Balluff Страницы: 2

Бренд: Hanna Instruments Страницы: 48

Бренд: Astute Medical Страницы: 86

Бренд: sauermann Страницы: 7

Nunes Instruments Propeller Type Water Current...

Бренд: V-tech Страницы: 19

Бренд: ATI Technologies Страницы: 70

Бренд: Omega Страницы: 55

Бренд: Apera Instruments Страницы: 30

Бренд: Saluki Страницы: 15

Бренд: Teledyne Lecroy Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды