background image

7.CORRECT DRIVING OPERATION

7-17

Attach chains on the tyres, when 
driving through snow or on icy roads.

Secure the tyre with chains so 
that they are not loose. Check 
them for looseness after driving 
for 5 to 10 minutes. Always keep 
i n  m i n d  t h a t  t h e  t y r e s  a r e 
mounted with chains.

Attach the tyre chains so that 
t h e  b e n d s  o f  t h e  t y r e  c h a i n 
connectors (1) are facing away 
from the tyre and with the chain 
bands (2) attached securely. Tie 
down any excess chain with wire 
to keep it from hitting the fender.

1. Wire              2. Hook

Fuel tank

Always keep the fuel tank filled 
to the maximum level to avoid 
corrosion in the fuel system.

Always tighten the fuel tank cap 
to avoid entry of dust, water and 
snow into the tank.

When parking

When parking for a long time in cold 
areas, choose a place where the 
vehicle will be out of snow fall. If an 
appropriate place is not available, 
park the vehicle so that the wind will 
not strike the engine compartment.

NOTE

• Do not attach tyre chains to the 

front wheels. Always attach 
suitable tyre chains to the rear 
wheels.

• There are various types of tyre 

chains. Please consult nearest 
UD Trucks authorised dealer 
for advice when purchasing 
tyre chains.

   DANGER

Fuel leaks could cause a fire. If 
there is a fuel leak, contact the 
nearest UD Trucks authorised 
dealer for assistance. 

   WARNING

 Always use good quality fuel. 

Содержание QUESTER Series





















































































































































































































































Отзывы: