Tuttnauer LabSci 11-V Скачать руководство пользователя страница 94

Страница: 94 / 97

Page 93

Message /
Symbol /
Problem

Failure Description

Corrective Action

Air Error

This message is displayed at
the end of the cycle If the
autoclave does not reach the
atmospheric pressure after
10 minutes.

Wait until the autoclave
reaches the atmospheric
pressure and perform a
new cycle.

Compressed
air supply
error

This message is displayed in
case of a compressed air
supply malfunction.

Check and fix the
compressed air supply.

Periodical
check time
exceeded -
Please call
for service

The periodical maintenance
time has passed.

Call for service.

Cycle
counter
exceeded -
Please call
for service

Number of cycles, since last
periodical maintenance,
exceeded the preset number
as defined by "cycle counter"
parameter.

Call for service.

Power Down

This message is displayed if
power down has occurred
during the cycle. (this
message will print out in the
printer after the autoclave will
turn on).

Turn on the autoclave
and wait until the
autoclave is ready
(reaches the safe
condition) and perform a
new cycle.

Supply
distilled
water error
(digitat input
option)

This message is displayed in
case of a mineral free water
supply malfunction.

Check and fix the
mineral free water
supply

Supply water
error (digitat
input option)

This message is displayed in
case of a city (tap) water
supply malfunction.

Check and fix the city
(tap) water supply.

Compressed
air supply
error (digitat
input option)

This message is displayed in
case of a compressed air
supply malfunction.

Check and fix the air
supply.

No Water

This message is displayed if
the electrode in the chamber
did not sense water within
the preset time.

check and fix the

mineral free water
supply.
2.check and clean the
water inlet filter.
3.

Clean the water

level electrode.

Analog Input
Error

This message is displayed
when any Temperature

Call for service.

Содержание LabSci 11-V


































































































Результаты поиска

Содержание LabSci 11-V

Отзывы:

Похожие инструкции для LabSci 11-V

Бренды по названию

Популярные бренды

Tuttnauer LabSci 11-V, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание LabSci 11-V

Отзывы:

Похожие инструкции для LabSci 11-V

Бренды по названию

Популярные бренды