Tuttnauer LabSci 11-V Скачать руководство пользователя страница 30

Страница: 30 / 97

Page 29

4.3

Displayed Error Messages / Symbols

The failures are divided into two categories

Failure that occur before completing the sterilization stage, which in
this case will leave the load unsterilized

Failure that occur after completing the sterilization stage, which in this
case will leave the load sterilized

For the list of

Displayed

Error Messages / Symbols

see sec. 12.

TROUBLESHOOTING

4.4

Displayed operational messages / Symbols

Message /

Symbol Name

Message /

Symbol

Description

Required Action

This symbol is displayed when
the door is open.

Close the door.

Door is open
(during stand by)

This message is displayed
when the door is opened: In
standby - if

START/STOP

preset.

Close the door to
perform a new cycle.

Cycle Ended

This message is displayed
when the cycle ended
successfully.

Press

START/STOP

perform a new cycle.

Test Ended

This message is displayed
when the test ended.

Press

START/STOP

perform a new test

This symbol is displayed when
Cycle by Clock mode is
performed.

Enter the Admin menu
as described in this
manual to change the
time or to cancel this
option.

Cycle by clock

This message is displayed if
the user presses

START/STOP

key while the

"cycle by clock" mode is
active.

Enter the Admin menu
as described in this
manual to change the
time or to cancel this
option.

Atmospheric
pressure not set

This message id displayed to
set the atmosphere pressure
by opening the door for 5
minutes.

Open the door for 5
minutes to set the
Atmospheric pressure.

Содержание LabSci 11-V


































































































Результаты поиска

Содержание LabSci 11-V

Отзывы:

Похожие инструкции для LabSci 11-V

Бренды по названию

Популярные бренды

Tuttnauer LabSci 11-V, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание LabSci 11-V

Отзывы:

Похожие инструкции для LabSci 11-V

Бренды по названию

Популярные бренды