Tuttnauer LabSci 11-V Скачать руководство пользователя страница 95

Страница: 95 / 97

Page 94

Message /
Symbol /
Problem

Failure Description

Corrective Action

sensor or Pressure sensor is
disconnected or out of range.

Chamber
temperature
not in range

This message is displayed if
the temperature in the
chamber is too high or too
low from the normal range.

Call for service.

Chamber
pressure not
in range

This message is displayed if
the pressure in the chamber
is too high or too low from the
normal range.

Call for service.

I/O Card
Failed

This message is displayed if
I/O card is faulty (both while
cycle is running or not).

Call for service.

I/O card is
not
connected

This message is displayed if
I/O card is disconnected
(both while cycle is running
or not).

Call for service.

Low
Vacuum’ is
displayed

Message is displayed and
FAIL indicator lights if in the
air removal stage, a vacuum
level of 15kPa is not reached
during 20minutes after the
cycle is started

Perform a new

cycle.

2

Call the

technician.
3

The bio-hazard

filter may be clogged.
Since the door cannot
be opened until a
complete successful
cycle is completed

– call

for technical service.

Содержание LabSci 11-V


































































































Результаты поиска

Содержание LabSci 11-V

Отзывы:

Tuttnauer LabSci 11-V, Руководство по эксплуатации и обслуживанию, Страница: 95 / 97

Результаты поиска

Содержание LabSci 11-V

Отзывы: