Trinity Highway QuadGuard Elite M10 Wide Скачать руководство пользователя страница 34

Страница: 34 / 68

TrinityHighway.com

Revision A August 2020

Note:

Mushroom Washers lay flat against the Fender Panel as shown below. Mushroom Washer
Stand-off must be seated completely through slot (Figure 35).

Continue attaching Fender Panels until you reach Diaphragm No. 1 (Figure 36).

15) Belt Nose Assembly

a. Using 5/8X5” hex bolts, 5/8X1 3/4” flat washers, and 5/8” hex nuts, attach Fender

Panels to Diaphragm Hinge Plates on three places per side (Figure 37 and 38). Tighten
all fasteners.

b. Thread additional 5/8” nuts onto the 5/8X5” hex bolts. Slide 5/8X1 3/4" flat washers onto

bolts (three places per side). Adjust the nuts so the outside of the washers are even
with the Fender Panel humps (Figure 37).

c. Place Belt Nose over Diaphragm/Fender Panel attachment bolts.

d. Align holes in Belt Clamps with bolts and place onto bolts against belt.

e. Secure with 5/8X1 3/4” washers and 5/8” hex nuts in three places per side. Adjust Belt

Nose Assembly so belt height is 32.0” above grade. Tighten all fasteners.

f. Complete Belt Nose Assembly by attaching Belt to Nose Cylinder with 1/2X3” hex bolt,

1/2” washer, lock washer, and hex nut.

Figure 36

Diaphragm No. 1 & Cartridge Placement

Figure 35

FENDER PANEL

MUSHROOM

WASHER

CORRECT

INCORRECT

STAND-OFF

DIAPHRAGM #1

ME2

ME3

ME1

QEN

Содержание QuadGuard Elite M10 Wide





































































Результаты поиска

Содержание QuadGuard Elite M10 Wide

Отзывы:

Похожие инструкции для QuadGuard Elite M10 Wide

Бренды по названию

Популярные бренды

Trinity Highway QuadGuard Elite M10 Wide, Руководство по сборке изделия

Результаты поиска

Содержание QuadGuard Elite M10 Wide

Отзывы:

Похожие инструкции для QuadGuard Elite M10 Wide

Бренды по названию

Популярные бренды