Trinity Highway QuadGuard Elite M10 Wide Скачать руководство пользователя страница 38

Страница: 38 / 68

TrinityHighway.com

Revision A August 2020

QuadGuard

Elite M10 Wide Final Inspection Checklist

Site Location: ___________________________

Date: __________________________________

Inspector: ______________________________

Refer to the QuadGuard

Elite M10 Wide manual and/or drawing package.

Proper Transition Panel is used for barrier type (p. 11)

If no transition is used, side panels are used with backup (p. 11)

Minimum clearance of 25” behind rear Fender Panels for movement (p. 14)

Anchor nuts are torqued to adhesive manufacturer’s specification (p. 16)

Cylinder types are properly placed (p. 19)

Every borehole and slot in Backup and Monorail is utilized (pp. 23, 24)

Anchor stud(s) height is 1 1/2” [38 mm]or less above the pad (p. 24)

Monorail guides are attached to the Diaphragms (p. 26)

Cylinder Segments are fastened on each side of the 1

Diaphragm (p. 27)

Monorail End Cap Assembly in place (p. 27)

Mushroom

Washer

Assembly

nuts must be tightened to the bolt shank. (p. 32)

Mushroom Washers tabs lay flat within Fender Panel slots (pp. 33, 39)

Belt Nose Assembly and is 32” above grade (p. 33)

Fender Panel gap is 1.0” [25 mm] or less for Wide systems (p. 43)

Bolts and nuts are properly tightened throughout the system (p. 43)

System is clear of debris

Содержание QuadGuard Elite M10 Wide





































































Результаты поиска

Содержание QuadGuard Elite M10 Wide

Отзывы:

Похожие инструкции для QuadGuard Elite M10 Wide

Бренды по названию

Популярные бренды

Trinity Highway QuadGuard Elite M10 Wide, Руководство по сборке изделия

Результаты поиска

Содержание QuadGuard Elite M10 Wide

Отзывы:

Похожие инструкции для QuadGuard Elite M10 Wide

Бренды по названию

Популярные бренды