Tri-Star M100LFG-TT/150 Скачать руководство пользователя | Manualshive

Страница: 34 / 73

background image

34

Fig.9.5. Run window

RUN

button starts the production. The process automatically starts from the highlighted

wires and continues to the last wire in the list. If more than one set is required, the job
then starts again from the first wire in the list.

STOP

button halts the process. The job then can be resumed from the point it was

interrupted.

Laser ON/OFF

buttons turn laser on and off. When the laser is turned off

Laser is OFF

label is visible. When

the laser is switched on and all alarms are cleared

the label changes to

Laser is Ready

and

RUN

button becomes active.

Warming Up

label appears when the laser is warming up. The temperature stabilization progress is
shown by a moving bar on the bottom of the screen. The warm up period is set in the
Parameters Screen and should not be changed unless advised by the authorized factory
representative.

PULL

button starts the motors in the manual mode

MARK

button prints currently selected message. It allows marking a single message on

a wire or any other substrate (e.g. shrink tubing) without engaging the wire pulling
mechanism (manual mode). The message box can have up to 5 lines. The length of the
message is determined by the longest line. The displayed time is a time required to print
the entire message. Marking parameters such as font, scale, character and multiline
spacing are defined in the processing screen on main window (Fig.9.1).

STOP

button disables the laser and the motors.

CUT

button activates the cutting cycle in the manual mode

CLOSE

button closes the Run screen and opens the Main screen.

RESET

button resets alarms.

Manual Mode

pauses the machine after each wire is printed. Press

CONTINUE

button

to process the next wire. Manual mode can be activated and deactivated any time during
the production run.

Mark on Fly

switches the machine for printing on the moving wire. This mode is used in

the high volume high production when machine stops only for cutting the wire.

«
...
32
33
34
35
36
...
»

Содержание M100LFG-TT/150










































































Отзывы:

Нет отзывов

Похожие инструкции для M100LFG-TT/150

DigitalFlow GF868

Бренд: GE Страницы: 80

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Badger Meter Страницы: 56

ModMAG M Series

Бренд: Badger Meter Страницы: 4

Бренд: Camille Bauer Страницы: 62

Бренд: jablotron Страницы: 2

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 7

Бренд: Yamaha Страницы: 60

GranTouch Digital Grand Piano

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 47

Бренд: Daewoo Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды