Tri-Star M100LFG-TT/150 Скачать руководство пользователя | Manualshive

Страница: 4 / 73

background image

4

1. INTRODUCTION

The M100LFG-TT/150 is a computer-controlled, Ultra-Violet Laser Wire and Cable

Marker and Processor. The system marks the wire pulled from a spool then cuts and coils it to
specified lengths. Precise heavy-duty pulling mechanism consists of two working in sync stepping
motors and pneumatic cutter. The cut wire exits the machine and is automatically coiled for easy
handling. XY scanning beam technology allows marking with different fonts, sizes, orientations
and print densities. Standard software package has number of fonts for English language, barcode
3 of 9 and some other symbols. Special symbols and foreign languages may be supported per user
request.

The M100LFG-TT/150 is fully programmable. The program routines include set up and

adjustments of pulling and cutting processes, laser and scanner parameters, marking patterns, etc.
When malfunctions occur, the process stops automatically and specified error message appears
on the screen.

A marking task consists of entering message, separate space between the messages and

cutting length for each wire, and also selecting a font, size and print density. The task is loaded
to a dedicated computer from keyboard, CD, memory stick, or through the Local Area Network.
Then it can be stored in the system memory and accessed any time needed.

These features enable the M100LFG-TT/150 to automatically mark large batches of

wires for mass production. They also enable cost-effective production for individual harnesses
without expensive machine changes between kits.

«
...
2
3
4
5
6
...
»

Содержание M100LFG-TT/150










































































Отзывы:

Нет отзывов

Похожие инструкции для M100LFG-TT/150

Бренд: 3nh Страницы: 10

Бренд: Kawai Страницы: 66

Бренд: Galileo Страницы: 19

Бренд: Galileo Страницы: 71

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hammond Страницы: 16

Бренд: JAMAR Technologies Страницы: 4

Бренд: Jamar Страницы: 60

Бренд: Oldham Страницы: 34

Бренд: Seben Страницы: 16

Бренд: AKCP Страницы: 16

Бренд: Swann Страницы: 106

Бренд: AEMC Страницы: 20

Бренд: Eddy Wireless Страницы: 18

Expert PDU energy 8001

Бренд: Gude Страницы: 22

Бренд: ILITCH ELECTRONICS Страницы: 2

Бренд: East Tester Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды