Tri-Star M100LFG-TT/150 Скачать руководство пользователя | Manualshive

Страница: 18 / 73

background image

18

The laser beam dump underneath of the scanner is used during the internal laser power

measurement process.

Fig.4.5 Beam Delivery System

Deflection mirrors scan the laser beam according to a specified pattern similarly to a hand

writing process. 200 mm objective focuses the beam on the tablet surface. The laser fires 50000
shots per second leaving one permanent marking dot on the surface per shot. The dot diameter
varies from about 100 to 200um and mostly depends on the laser pulse energy, focusing
objective, and surface composition. The distance between the dots is completely programmable
and depends on the speed of the moving mirrors and laser repetition rate. The system allows
imprinting any information on the wire surface including logos, pictures, barcodes, and
alphanumeric messages.

Laser is equipped with locking key switch. During the operation the key should be in ON

position and laser shutter should be open. The laser is externally controlled by the scanner board.
All laser parameters are downloaded from the computer.

Warning !!!

Do not press any buttons and/or change any settings on the

laser power supply unless instructed by authorized personnel.

When laser is powered, warmed up and ready to operate it produces a low power pilot

beam when switched to the alignment mode (offset). The beam footprint should be visible on the
loaded wire or on a piece of white paper under the beam. For detailed laser description refer to
Appendix A.

Scanner

To the
Scanalone
Board

Objective

Shutter

To the
Safety
Relays

Beam
Path

Laser
Exit Beam
Opening

Telescope
defocusing
lens

Telescope
focusing
lens

«
...
16
17
18
19
20
...
»

Содержание M100LFG-TT/150










































































Отзывы:

Нет отзывов

Похожие инструкции для M100LFG-TT/150

Бренд: Samson Страницы: 4

Бренд: Oceanic Страницы: 152

Бренд: Kaiterra Страницы: 8

Бренд: Kaiterra Страницы: 12

Бренд: MULTISPAN Страницы: 2

Бренд: Motortech Страницы: 142

Бренд: MICRO-EPSILON Страницы: 82

Бренд: Jaquet Страницы: 27

Бренд: Kinesys Страницы: 10

Бренд: REED Страницы: 20

WJ-NX310K Series

Бренд: i-PRO Страницы: 18

Бренд: CWT Страницы: 41

Бренд: Megasat Страницы: 25

Бренд: Thermocable Страницы: 10

Бренд: J-TECH Страницы: 3

Бренд: SV Страницы: 88

Бренд: ASD Страницы: 72

Бренд: OHAUS Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды