Tri-Star M100LFG-TT/150 Скачать руководство пользователя | Manualshive

Страница: 22 / 73

background image

22

The bottom stepping motor along with its pulling belt is mounted on the air cylinder

actuated by the toggle switch. That opens the gap between the belts for easy loading/unloading of
a new wire. Air pressure regulators on the back of the system set belts pressure on the wire for
encoder and pulling mechanisms (Fig.4.10). Standard pressure is set around 30 psi; however, it
can vary depending on the wire gauge and mechanical properties of the insulation. Belts can be
easily removed from the pulleys and replaced by loosening belt tension rollers.

Fig.4.10. Pressure regulators and Electrical panel.

PLC controls the movements of pulling belts by supplying pulses of appropriate

frequency to the stepping motor drivers. It pulls the wire for a specified length and triggers the
marking when needed. Once the required length is processed it stops the wire and activates a
solenoid valve that supplies air pressure to a pneumatic cutter. Air pressure regulator for the
cutter on the back of the system is normally set to 80 psi. The pressure can be increased for small
gauge solid conductor wires and cables. PLC also synchronizes coiling pan spinning with wire
movement, monitors pressure, interlocks and laser-scanner malfunctions. Fig.4.7 shows all major
electrical components. Encoder belts move with the speed of wire producing the encoder pulses
supplied directly to the scanner. Scanalone board reads the encoder pulses and automatically
corrects the marking for the current wire speed allowing message printing on the fly.

Optional motorized prefeed is mounted on a separate cart on the left side of the laser

marker. It consists of the spool shaft connected to the AC motor, two pairs of wire pulleys on a
dancer shaft, top and bottom limit switches and speed regulator. When the wire starts moving the
bottom pulleys move up and the motor spins the spool faster. An excess of wire in the loop
causes the bottom pulleys to drop back down and reduces the motor speed. This specially
designed dancing mechanism coupled directly with the motor allows maintaining the proper wire
tension without jerking the wire.

It is recommended to ground the tail end of the wire to prevent accumulation of the static

charges during wire processing. Occasional arcing between grounded blades and excessively
charged wire during the cutting process creates intensive electrical noise that may interfere with
marking controller.

Leveler

Pressure
switch

PLC

Stepping
Motor
Drivers

Scanalone
Board

24 and
+/-15VDC
Power Supplies

Safety Relays

Wire
Sensor
amplifier

Pulling
pressure

Encoder belts
pressure

Cutting
pressure

«
...
20
21
22
23
24
...
»

Содержание M100LFG-TT/150










































































Отзывы:

Нет отзывов

Похожие инструкции для M100LFG-TT/150

Бренд: DAKOTA ULTRASONICS Страницы: 25

Бренд: DAKOTA ULTRASONICS Страницы: 36

Бренд: Tactical Controls Страницы: 11

Бренд: FarmChem Страницы: 8

Бренд: Kamstrup Страницы: 100

Бренд: Kamstrup Страницы: 16

Бренд: Kamstrup Страницы: 12

Бренд: Kamstrup Страницы: 60

Бренд: Kamstrup Страницы: 136

Бренд: Kamstrup Страницы: 16

Бренд: Kamstrup Страницы: 155

Бренд: VeEX Страницы: 842

Бренд: National Instruments Страницы: 18

Бренд: Oceanic Страницы: 68

Бренд: Oceanic Страницы: 24

Бренд: TA Instruments Страницы: 7

Бренд: Lake Shore Cryotronics Страницы: 97

Бренд: ESP Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды