Tri-Star M100LFG-TT/150 Скачать руководство пользователя

Страница: 39 / 73

•

Laser On

button turns the pilot beam on.

•

Laser Off

button turns the beam off.

•

The

up/down

and

left/right

arrows move the beam across and along the wire

respectively.

•

Test

button is used for checking the alignment.

•

Save

button saves current setting.

•

Pull

button moves the stepping motors the length specified in

Pull Length.

•

Marking window

defines the length of the marking zone along the wire.

•

Angle

defines the difference between X axis of the scanner and wire center line.

Make an alignment in the following order:

Load 20 to 24 gauge wire.

Turn on the laser.

Observe low power beam footprint on the wire

Using the arrows move the beam to the left side of the wire channel as shown on Fig.9.8.

Click Save button to save start-mark position. Every message will be printed starting
from this position and farther to the right.

Press the Test button. The beam should jump to the right on a distance specified in the
Marking Window. Check for the beam footprint on the wire.

If the footprint is not on wire center line change the angle and press the Test button again.

Repeat step 7 until the beam footprint is on the wire center.

Click

SAVE

button

Содержание M100LFG-TT/150










































































Результаты поиска

Содержание M100LFG-TT/150

Отзывы:

Похожие инструкции для M100LFG-TT/150

Бренды по названию

Популярные бренды

Tri-Star M100LFG-TT/150, Руководство пользователя

Результаты поиска

Содержание M100LFG-TT/150

Отзывы:

Похожие инструкции для M100LFG-TT/150

Бренды по названию

Популярные бренды