Trafox SUPERINTEND IC-01 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 73

Trafox SUPERINTEND IC-01 Скачать руководство пользователя страница 61

Superintend IMD

© Copyright Muuntosähkö Oy - Trafox

61

http://www.trafox.fi

PEC-01 UNIT

The PEC-01 unit measures the continuity and resistance of the PE wires connected to it.
The PE wire reference point (PE0) is connected to the switchboard’s PE rail and
continuity and resistance are measured against it from the last socket of each wall
socket chain (PE1…6). The IM-01.MED unit controls the functioning of the PEC-01 unit.
It gives the measurement commands via the bus, reads the measurement results and
based on these, determines the fault situations. If the PEC-01 unit does not respond to
the commands of the IM-01.MED unit within three seconds, the IM-01.MED unit gives
the REMOTE UNITS and WIRE FAULT errors. The PEC-01 unit displays a SYSTEM FAIL
error.

At the implementation, the IM-01.MED unit requests the PEC-01 unit to measure the
resistance of all channels connected to it and compiles a table. After that, the resistance
measurement only functions by separate request (MONITOR

→

PEResist Measure). IM-

01.MED compares the measured resistance values to the table values. If any resistance
value is higher than the alarm limit (the table value multiplied by the percentage
parameter PEalarm%), an alarm is given. The measurement range is 0…2.54 Ω. The
detection of a measurement loop break is constantly on.

R 472k

Ω

I 44%

Address:

0

Confirm?

0

Address:

1

Address:

4

...

Short

press

Cancel

Old address remains

5 s

press

Done

New address is saved

5 s

press

«
...
59
60
61
62
63
...
»

Содержание SUPERINTEND IC-01










































































Отзывы:

Нет отзывов