manualshive.com logo in svg

Trafox SUPERINTEND IC-01, Инструкция по установке и эксплуатации, Страница: 34 / 73

Поделиться
Скачать
Trafox SUPERINTEND IC-01 Скачать руководство пользователя страница 34

34

 

© Copyright Muuntosähkö Oy – Trafox

 

Superintend IMD 

 

http://www.trafox.fi

 

NETWORK VIEW / ADDING AND REMOVING DEVICES 

 

The Network View function, as well as the Network Scan function, scans ALL possible 
device addresses in the entire network. The scan is started by approving SCAN? Y/N in 
the screen mode of the menu: select Y and press T. After the scan, all devices detected 
and the connected PE unit channels in the AutoScroll mode toggle on the screen at one 
second intervals. The screen can be stopped with the   and   buttons, and the results 
can be browsed manually using those buttons.  

If the device already has a previously approved configuration, the AutoScroll mode 
displays the measured value of each parameter and the approved value from an earlier 
configuration saved in the EEPROM memory.   

The results are approved with the T button, and a confirmation is then requested: 
Confirm Add?/Confirm Delete?/Confirm Change?, as applicable. When Y is selected, the 
changed value is saved in the memory of the IM-01.MED unit. All changed parameters 
(when adding a PE unit, also all its channels being used) must be approved one by one. 
The values that are not approved separately will retain their previous value. 

The screen mode of the Network View is similar to that of the Network Scan mode. 

Содержание SUPERINTEND IC-01










































































Отзывы:

Нет отзывов