manualshive.com logo in svg

Trafox SUPERINTEND IC-01, Инструкция по установке и эксплуатации, Страница: 24 / 73

Поделиться
Скачать
Trafox SUPERINTEND IC-01 Скачать руководство пользователя страница 24

24

 

© Copyright Muuntosähkö Oy – Trafox

 

Superintend IMD 

 

http://www.trafox.fi

 

The most important alarms are indicated by a red LED light, which BLINKS in fault 
situations and is on STEADILY if the fault has been fixed but not acknowledged (the OLD 
ALRM mode). 

When navigating the menu, the warning LED lights indicate which menu item is in use. 

The insulation resistance fault activates IMMEDIATELY when the measured parameter 
drops below the alarm limit. The delay set for the alarms applies to all faults except the 
insulation resistance measurement. The value to be measured must consistently be 
above the alarm limit for the length of the delay before an alarm is given. If the 
measured quantity drops below the alarm limit during the delay, time counting restarts. 

In addition, all alarms have a five-percent hysteresis. In other words, an alarm becomes 
active when the set limit is reached, but it is deactivated only when the measured value 
deviates by 5% in a safe direction from the limit given. 

The screen mode of each parameter 

alternately displays the following: 

 

On the top row, the value / fault limit of the parameter that caused the fault, and 
on the bottom row, the current status: OK, ALARM or OLD ALRM 

 

Fault start time and date 

If the fault has been deactivated and becomes active again, the start time of the active 
fault is displayed.  In items InstUnit, WireAmpl and WireOffs, there may be several 
faults, which are displayed one after the other. In the OK mode, nothing is displayed in 
the screen mode. 

The screen always displays the smallest value (insulation resistance) or largest (all other 
measurements) value / fault limit measured during the fault first, followed by the fault 
start time.  

 

The temperature alarm has been deactivated but not 
acknowledged. 

The largest value measured during the fault, the alarm limit's set 
value and the fault start time are displayed. 

 

 

The temperature alarm is active. 

The highest temperature measured during the fault is 93 
degrees and the alarm limit is 90 degrees. 

 

 

 

 

 

 

 

 

 

 

 

Содержание SUPERINTEND IC-01










































































Отзывы:

Нет отзывов