Trafox SUPERINTEND IC-01 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 73

Trafox SUPERINTEND IC-01 Скачать руководство пользователя страница 33

Superintend IMD

© Copyright Muuntosähkö Oy - Trafox

33

http://www.trafox.fi

Examples of the screens of the Network Scan screen mode:

Channel 1 of the PEC-01 unit is not connected.

Channel 2 of the PEC-01 unit 15 is connected, the measured
new value is 0.70 Ω and the previous approved value was
1.2 Ω.

Channel 1 of the PEC-01 unit 9 is connected but its
resistance is more than 2.55 Ω. The previous approved
value was 0.4 Ω.

Channel 2 of the PEC-01 unit 8 is connected but its
resistance is more than 2.55 Ω. The channel was not
connected at all in the previous approved configuration.

Channel 1 of the PEC-01 unit 8 is connected and its
resistance is 0.20 Ω. The channel was not registered in the

previous approved configuration.

The IC-01 unit 8 is connected, and it was also included in an

earlier approved configuration.

The TC-01 unit 8 is new.

The RD-01 unit 2 has been removed from the previous

approved configuration.

«
...
31
32
33
34
35
...
»

Содержание SUPERINTEND IC-01










































































Отзывы:

Нет отзывов