THORLABS K-Cube Piezo Controller Скачать руководство пользователя страница 42

Страница: 42 / 78

HA0365T Rev D Jan 2017

Chapter 5

possible to adjust the DC level on the output whilst adding an AC signal to this DC

level via the external SMA terminal.

5.5 Operation with Other members of the K-Cube Family

5.5.1 Introduction

The operation of the KPZ101 piezo controller can be extended when the unit is used

in conjunction with othe r members of t he K-Cube family. Speci fically, 2 othe r

controllers have been designed to work cl osely with the KPZ 101 piezo unit; the

KSG101 strain gauge reader and the TNA001 NanoTrak autoalignment controller.

When the KPZ101 piezo controller is used with a KSG101 strain gauge reader, closed

loop operation is possible, which allows more stable and precise position control than

open loop - see Section 5.6.
When used with the TNA001 NanoTrak controller and a laser light source such as the

TLS001 laser source cube, automatic fiber alignment systems can be built - see the

handbook supplied with the NanoTrak unit for more information.
With both the KSG101 and the TNA001 it is possible to build a system without the

KCHx01 USB controller hub, however, in this case individual power supply and USB

connections are required for each controller in addition to the external signal cables

between the controllers. Using the KCHx01 hub greatly simplifies the system because

the hub provides all the necessary po wer, signal and USB conn ections to all the

controller cubes.

5.6 Closed Loop Operation

The following procedures explain the basic operation of the Piezo Driver K-Cube

when used in conjunction with a Strai n Gauge Reader K-Cube. Section 5.6.1.

explains operation on the KCHx01 USB Controller hub, while Section 5.6.2. explains

the various bay mounting options and the associated software settings.

Section 5.6.3. explains use off the hub, with exte rnal wiring via the rear panel

connections.

5.6.1 Electrical Connections and Software Settings - Hub Operation

The following procedure describes a typical set up, when a KPZ101 piezo driver cube

and a KSG101 Strain Gauge Reader are used on the KCHx01 controller hub to drive

a piezo actuated stage - see Fig. 5.8 for a general system schematic diagram.

Note

When the KPZ101 is used in closed loop mode with the KSG101 Strain Gauge

Reader, it is not possible to modulate the KPZ101.

Содержание K-Cube Piezo Controller















































































Результаты поиска

Содержание K-Cube Piezo Controller

Отзывы:

Похожие инструкции для K-Cube Piezo Controller

Бренды по названию

Популярные бренды

THORLABS K-Cube Piezo Controller, Руководство пользователя

Результаты поиска

Содержание K-Cube Piezo Controller

Отзывы:

Похожие инструкции для K-Cube Piezo Controller

Бренды по названию

Популярные бренды