THORLABS K-Cube Piezo Controller Скачать руководство пользователя страница 23

Страница: 23 / 78

K-Cube Piezo Driver

4.3 Velocity Wheel Operation

The velocity wheel/joystick is an infinite turn potentiometer, which is used to ini tiate

different types of move depending on its mode setting. The mode can be set either

via the GUI Settings panel, see Section 6.2.2. or via the top panel display menu, see

Section 4.4.

4.3.1 Voltage Adjust Mode

In voltage mode, the wheel can be used to increase and decrease the drive voltage.

The voltage change is proportional to the deflection of the wheel - see Section 4.4.7.

The rate of change is adjusted in the Joystick Menu parameter - see Section 4.4.8.

4.3.2 Go to Voltage

In ‘Go To Voltage’ mode, two preset voltage values can be specified, such that the

drive voltage is set to voltage 1 when the wheel is moved down, and to voltage 2

when it is moved up. These ‘taught’ voltages can be set through the software GUI -

see Section 6.2.2. or via the display menu, see Section 4.4.7.
This mode of operation is enabled by setting the ‘Wheel Mode’ to ‘Go to voltage’

through the software GUI - see Section 6.2.2. or via the display menu, see Section

4.4.7.

4.3.3 Jog to voltages

The top panel wheel can also be configured to ‘jog’ the drive voltage. This mode of

operation is e nabled by setting the ‘ Wheel Mode’ parameter to ‘Jog to voltage’

through the software GUI - see Section 6.2.2. or via the display menu, see Section

4.4.7.

Содержание K-Cube Piezo Controller















































































Результаты поиска

Содержание K-Cube Piezo Controller

Отзывы:

Бренды по названию

Популярные бренды

THORLABS K-Cube Piezo Controller, Руководство пользователя

Результаты поиска

Содержание K-Cube Piezo Controller

Отзывы:

Бренды по названию

Популярные бренды