manualshive.com logo in svg

THORLABS K-Cube Piezo Controller, Руководство пользователя, Страница: 26 / 78

Поделиться
Скачать
THORLABS K-Cube Piezo Controller Скачать руководство пользователя страница 26

26

HA0365T Rev D Jan 2017

Chapter 4

4.4.2 Menu Option - HV output

This mode is used to enable or disable the drive output.

Press  the  MENU bu tton,  then  use the   wheel  to scroll

through the menu options.

Press the MENU button to enter the 1 HV output option.

The display shows the current setting.

Use the wheel to enable/disable the output.

Press the MENU button to store the selection and return

to the operating screen.

4.4.3 Menu Option - Voltage range

The piezo actuator connected to the cube has a specific

maximum operating voltage range. This mode is used to

set the maximum drive voltage for the actuator connected

to the unit.
Press  the  MENU bu tton,  then  use the   wheel  to scroll

through the menu options.

Press  the  MENU button to e nter  the  2 Vo ltage  range

option.

The display shows the current setting.

Use  the  wheel  to  set  the  voltage  associated  with  your

piezo actuator, 75V, 100V or 150V.

Press the MENU button to save the setting and return to

the operating screen.

M e n u   o p t i o n s
U s e   w h e e l

M e n u   o p t i o n s
1   H V   o u t p u t

H V   d i s a b l e d
    t o   c h a n g e

MENU

H V   e n a b l e d
    t o   c h a n g e

V o l t a g e :   0 . 0 0 V

                  7 5 V   N   V

O u t p u t   i n a c t i v e

                        7 5 V   N   V

M e n u   o p t i o n s
2   V o l t a g e   r a n g e

M e n u   o p t i o n s
U s e   w h e e l

MENU

R a n g e   7 5 V
    t o   c h a n g e

V o l t a g e :   0 . 0 0 V

                  7 5 V   N   V

R a n g e   1 5 0 V
    t o   c h a n g e

V o l t a g e :   0 . 0 0 V

                  1 5 0 V   N   V

Содержание K-Cube Piezo Controller















































































Отзывы:

Нет отзывов