THORLABS K-Cube Piezo Controller Скачать руководство пользователя страница 55

Страница: 55 / 78

Chapter 6 Software Reference

6.1 GUI Panel

The following screen shot shows the graphical user interface (GUI) displayed when

accessing the controller using the APTUser utility.

Fig. 6.1 KPZ101 Piezo Driver Software GUI

Output Control

- used to adjust and set the voltage or position output as displayed

in the main digital display. If the channel is in closed loop mode then this control can

be used to adjust position output. If open loop mode is selected then the control is

used to adjust the voltage output.

Jog

- used to increment or decrement the output voltage. When the button is clicked,

the piezo is driven in the selected direction, one step per click. The step size can be

set in the 'Settings' panel or by using the SetJogStepSize method.

Volts Display

- shows the voltage applied to the piezo.

Note

The serial number of the KPZ101 unit associated with the GUI panel, the

APT server version number, and the version number (in brackets) of the

embedded software running on the unit, are displayed in the top right

hand corner. This information should always be provided when

requesting customer support.

Содержание K-Cube Piezo Controller















































































Результаты поиска

Содержание K-Cube Piezo Controller

Отзывы:

Бренды по названию

Популярные бренды

THORLABS K-Cube Piezo Controller, Руководство пользователя

Результаты поиска

Содержание K-Cube Piezo Controller

Отзывы:

Бренды по названию

Популярные бренды