manualshive.com logo in svg

THORLABS K-Cube Piezo Controller, Руководство пользователя

Поделиться
Скачать
THORLABS K-Cube Piezo Controller Скачать руководство пользователя страница 56

56

HA0365T Rev D Jan 2017

Chapter 6

Voltage Range Display

 - shows the maximum working voltage of the associated

piezo actuator.

Open Loop and Closed Loop

 

LEDs

 - When Open Loop or Closed Loop mode is

selected, the corresponding LED is lit.

Settings  display

  - shows the   name  of  the  associated  K-Cube  together  with the

following user specified settings:

Jog Step Size

 - the distance to move when a jog command is initiated. If in closed

loop mode, the step size is measured in microns; if in open loop mode, the step

size is measured in Volts. The step  size can be set either via the Settings panel

or by calling the SetJogStepSize method. 

Input Source

 - displays the input source that controls the Piezo Driver output voltage. 

When the unit is in open loop mode, this line displays the Input Source. The input

source is a combination of the software with optionally either the potentiometer or

one  of  the 3   external  input  options  (SMA  connector,  Hub  Channel  1 or Hub

Channel 2) added in. 
When the unit is in closed loop mode, this line displays where the unit takes its

feedback input from (SMA connector, Hub Channel 1 or Hub Channel 2) and what

controls the position (software only or so potentiometer). 

If 

SW only 

 is displayed, the unit responds only to software inputs and the HV

amp  output  is  that  set usin g  the  SetVoltOutput  method  (or th e  GUI  panel

‘Output’ control).
If 

EXT_IN 

 is displayed, the unit sums the signal on the rea r panel ‘EXT IN’

SMC connector with the voltage set using the SetVoltOutput method (or the

GUI panel ‘Output’ control).
If

 Pot 

 is displayed, the unit sums the voltage set using front panel OUTPUT

control with the voltage set using the SetVoltOutput method (or the GUI panel

‘Output’ control).
If 

Pot_EXT_IN 

is  displayed,  the  unit  sums  the  voltage  set  using  front pan el

OUTPUT control with the voltage set using the SetVoltOutput method (or the GUI

panel ‘Output’ control) and the signal on the rear panel EXT IN SMC connector.
For example, if 

SW only

 is displayed, the output voltage is controlled by the

GUI 'Output' control knob (or the SetVoltOutput method) only. Turning the pot

or varying the voltage on the SMA input has no effect. If, however, 

SMA Input

+ Potenti Software

 is displayed, then the output voltage is the sum of

the contribution of these three factors.

Settings button

 - Displays the 'Settings' panel, which allows the tuning parameters

to be entered - see Section 6.2.

Ident

 - when this button is pressed, the front panel LED and digital display of the

associated controller K-Cube will flash for a short period.

Active

 - lit when the unit is operating normally and no error condition exists.

Error

 - lit when a fault condition occurs:

Содержание K-Cube Piezo Controller















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды