THORLABS K-Cube Piezo Controller Скачать руководство пользователя страница 43

Страница: 43 / 78

K-Cube Piezo Driver

The K-Cube positions on the hub and associated parameter settings described are by

no means the only possible options. For further information, see Section 5.6.2..

Fig. 5.8 Typical System Set Up - Hub Operation

1) Perform the mechanical installation as detailed in Section 3.2. of this manual and

also in the manual supplied with the K-Cube Strain Gauge Reader.

2) Install the K-Cube units onto the controller hub. Fit the Piezo unit in bay 1, and

the Strain Gauge Reader in bays 2 as shown in Fig. 5.8.

3) Connect the HV OUT terminal on the rear of the Piezo driver to the associated

piezo actuator.

4) Connect the STRAIN GAUGE I/P terminal on the rear panel of the strain gauge

unit to the Feedback connector on the piezo actuator.

5) Connect the controller hub to the power supply - see Section 3.3.2.
6) Connect the PSU to the main supply and switch ‘ON’. The version number of the

embedded software is displayed on the Piezo unit during boot up. The software

version is useful when requesting technical support. The ident number of the

associated K-Cube bay on the hub is also displayed.

7) Connect the controller hub to your PC.

8) Windows

should detect the new hardware. Wait while Windows

installs the

drivers for the new hardware - see the Getting Started guide for more information.

9) Run the APTUser utility

Start/All Programs/Thorlabs/APT/APT User.

10)Click the ‘Settings’ button on GUI of the Piezo Driver to display the Settings panel

(shown below).

Note

The USB cable should be no more than 3 metres in length.

Communication lengths in excess of 3 metres can be achieved by using

a powered USB hub).

to piezo actuator

drive terminal

to piezo actuator

feedback terminal

Strain Gauge Reader

MENU

Piezo Controller

MENU

Содержание K-Cube Piezo Controller















































































Результаты поиска

Содержание K-Cube Piezo Controller

Отзывы:

Похожие инструкции для K-Cube Piezo Controller

Бренды по названию

Популярные бренды

THORLABS K-Cube Piezo Controller, Руководство пользователя

Результаты поиска

Содержание K-Cube Piezo Controller

Отзывы:

Похожие инструкции для K-Cube Piezo Controller

Бренды по названию

Популярные бренды