THORLABS K-Cube Piezo Controller Скачать руководство пользователя страница 69

Страница: 69 / 78

K-Cube Piezo Driver

GetKCubeTriggerParams

Sets the triggering parameters

GetOutputLUTParams

Gets the output voltage waveform (LUT) operating

parameters.

GetOutputLUTTrigParams

Gets the output voltage waveform (LUT) triggering

parameters.

GetOutputLUTValue

Gets a specific voltage output value in the voltage

waveform (LUT) table.

GetVoltOutput

Gets the HV output voltage.

GetVoltageOutputLimit

Gets the HV output voltage maximum limit.

Identify

Identifies the controller by flashing unit LEDs.

LLGetStatusBits

Gets the controller status bits encoded in 32 bit

integer.

LLSaveHWDefaults

Allows the current settings of the operation

parameters to b e saved into the onboard 'Flash'

memory of the hardware unit.

LoadParamSet

Loads stored settings for specific controller.

SaveParamSet

Saves settings for a specific controller.

SetControlMode

Sets the loop operating mode (open/closed).

SetDispIntensity

Sets the front panel LED display intensity.

SetHubAnalogueChanIn

Sets the hub analogue input channel used for close

loop operation.

SetIPSource

Sets the HV amplifier input source.

SetJogStepSize

Sets the jogging step size.

SetKCubePanelParams

Sets various parameters for the top panel controls

SetKCubeTriggerParams

Sets the triggering parameters

SetOutputLUTParams

Sets the output voltage waveform (LUT) operating

parameters.

SetOutputLUTTrigParams

Sets the output voltage waveform ( LUT) triggering

parameters.

SetOutputLUTValue

Sets a specific vo ltage output value in the voltage

waveform (LUT) table.

SetVoltOutput

Sets the HV output voltage (open loop).

SetPosOutput

Sets the output position (closed loop).

SetVoltageOutputLimit

Sets the HV output voltage maximum limit.

ShowEventDialog

Shows the event dialog when it has previously been

disabled using the EnableEventDlg method

StartCtrl

Starts the ActiveX Co ntrol (starts com munication

with controller)

Содержание K-Cube Piezo Controller















































































Результаты поиска

Содержание K-Cube Piezo Controller

Отзывы:

Бренды по названию

Популярные бренды

THORLABS K-Cube Piezo Controller, Руководство пользователя

Результаты поиска

Содержание K-Cube Piezo Controller

Отзывы:

Бренды по названию

Популярные бренды