manualshive.com logo in svg

THORLABS K-Cube Piezo Controller, Руководство пользователя

Поделиться
Скачать
THORLABS K-Cube Piezo Controller Скачать руководство пользователя страница 9

9

K-Cube Piezo Driver

2.3.3 APT Config Utility

There are many system par ameters and configuration settings associated with the

operation  of  the  APT  Server.  Most can   be  directly  accessed  using  the  various

graphical panels, however there are several system wide  settings that can only be

made 'off-line' before running the APT software. These settings have global effect;

such as switching between simulator and real operating mode and incorporation of

calibration data. 

The APTConfig utility is provided as a  convenient means for making these system

wide settings and adjustments. Full details on using APTConfig are provided in the

online help supplied with the utility.

Use of the APT  Config  utility is  covered  in  the PC tutoria l (Chapter 5)  and  in the

APTConfig online help file, accessed via the F1 key when using the APTConfig utility.

Содержание K-Cube Piezo Controller















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды