manualshive.com logo in svg

THORLABS K-Cube Piezo Controller, Руководство пользователя

Поделиться
Скачать
THORLABS K-Cube Piezo Controller Скачать руководство пользователя страница 31

31

K-Cube Piezo Driver

4.4.8 Menu Option - Joystick menu

This mode is used to set  various parameters depending

on the Joystick mode setting - see Section 4.4.7.

Press  the  MENU bu tton,  then  use the   wheel  to scroll

through the menu options.

Press  the  MENU  button  to  enter  the 6 Joystick menu

option.

The display shows the current setting.

If 

Jog voltage 

Joystick mode is selected in the previous

section,  deflecting  the  wheel  initiates  a  change  in  the

drive voltage, using the parameters specified by the 

Step

parameter.  To  change  the  step  size,  click  the  MENU

button when this option is displayed, then turn the wheel

to adjust the step size.
Press MENU to store the selection and return to the main

display.
If 

Voltage adjust 

Joystick mode is selected in the previous

section, the wheel can be used to increase and decrease

the drive voltage. The voltage change is proportional to

the deflection of the wheel according to the setting in the

Speed

 parameter as follows: 

Speed: high

 - Voltage adjusts at a high rate, 

i.e. 1 V per detent/click.

Speed: medium

  -  Voltage  adjusts  at  a  medium

rate, i.e. 100 mV per detent/click.

Speed: low 

- Voltage adjusts at a low rate, 

i.e. 10 mV per detent/click.

To change the adjustment rate, click the MENU button

when the 

Speed: 

option is displayed, then turn the wheel

to adjust the step size.

Press MENU to store the selection and return to the main

display.

M e n u   o p t i o n s
6   J o y s t i c k   m e n u

M e n u   o p t i o n s
U s e   w h e e l

MENU

S t e p :   2 . 5 0 V
    t o   c h a n g e

V o l t a g e :   0 . 0 0 V
                  1 5 0 V   A   J

S p e e d :   h i g h
    t o   c h a n g e

P o s i t i o n :   0 . 0 0 %

                  1 5 0 V   1   A

Содержание K-Cube Piezo Controller















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды