manualshive.com logo in svg

THORLABS K-Cube Piezo Controller, Руководство пользователя

Поделиться
Скачать
THORLABS K-Cube Piezo Controller Скачать руководство пользователя страница 13

13

K-Cube Piezo Driver

3.2 Mechanical Installation

3.2.1 Environmental Conditions 

Location

Indoor use only

Maximum altitude

2000 m

Temperature range

5

o

C to 40

o

C

Maximum Humidity

Less than 80% RH (non-condensing) at 31°C

To ensure reliable operation the unit should not be exposed to corrosive agents or

excessive moisture, heat or dust.
If the unit has been stored at a low temperature or in an environment of high humidity,

it must be allowed to reach ambient conditions before being powered up.

3.2.2 Mounting Options

The K-Cube Piezo Driver is shipped with a baseplate, for use when fitting the unit to

a breadboard, optical table or similar surface. 
For  multiple  cube  systems,  a  3-channel  and  6-channel  K-Cube  Controller  Hub

(KCH301 and KCH601). ) are also available - see Section 2.2. for further details. Full

instructions on the fitting and use of the controller hub are contained in  the handbook

available at www.thorlabs.com

Warning

The safety of any system incorporating this equipment is the 

responsibility of the person performing the installation.

Warning

Operation outside the following environmental limits may adversely 

affect operator safety.

Cautions

When siting the unit, it should be positioned so as not to impede the 

operation of the control panel buttons. 

Ensure that proper airflow is maintained to the rear of the unit

Содержание K-Cube Piezo Controller















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды