Thermo King 098916, Руководство по обслуживанию

Страница: 195 / 196

194
Commands Menu
- PTI Test
- Brief PTI Test
- Function Test
- Manual Function Test
- Power Management
Setpoint Menu
- Opti-Set
- Temp. Setp.
- Bulb Mode
- Evap Fan Spd
- Defrost Trm.
- Economy Mode
- Hum. Control
- Hum. Setp.
- AFAM
- AFAM Delay
- AFAM Rate
- C02 Max.
Enter a Temperature or
Humidity Setpoint
• Press F4 key.
• Type the new setpoint.
• Press and hold F4 key
until cursor stops
flashing.
Activate Humidity Contol
Economy Mode
• Press F4 key.
• Press F2 key to toggle
setting between OFF
and ON.
• Press and hold F4 key
until cursor stops
flashing.
ALARMS
Alarms Menu
• View and write down
all alarm code.
• Press F2 key to view
the next alarm code
• Clear alarm code by
correcting problem and
acknowledging the alarm.
• To acknowledge an alarm,
press F4 key with alarm
code in display.
DATA
- Ambient
- High Press
- High Pr Tmp
- Hum Val.
- Bat. Voltage
- Voltage
- Volt P1 P2
- Volt P2 P3
-
- Volt P3 P1
- Frequency
- Zero Current
- Curr. Ph. 1
- Curr. Ph. 2
- Curr. Ph. 3
- CO2
- Fresh Air Ex
RMM STATE
RMM Status
Display shows current status: • Offline
• Zombie • Online
DATALOGGER
Datalogger Menu
- Inspect Temp Log
- PTI State
- Inspect PTI Log
- Calibrate USDA Probe
- Activate Trip Start
- Set Log Time
- Inspect Event Log
Datalogger Submenu
• First function screen
appears:
- Inspect Temp log:
Press F4 key to view next
screen. Press F3 key to
scroll through previous logs
of sensors.
- Inspect Event Log:
Press F3 key to scroll
through previous even
logs.
- Set Log Time: Press F3
key to scroll through log
interval list. Press and
hold F4 key until cursor
stops flashing.
- Activate Tripstart:
Press F4 key to
enter trip
start
maker.
- Inspect PTI Log:
Press F3 key
through test result
screens.
CONFIGURATION
Configuration
Menu
- Cont ID
- Ctrl Type
- In Range
- Economy Max
- Economy Min
- Unit Type
- Zero Current
-Supply LH
- AFAM Opt.
- Gas Analyzer
- AFAM Units
- Evap. Type
- Cond. Type
- Chart R.
- Auto Config.
- Unit #
- Unit ID
Configuration
Submenu
• Current function
setting appears
in display.
• Press F4 key to
change a
setting.
• Press F3 key, “A”
key (password),
F4 key and EXIT
key.
• Type new value;
or press F3 key
to toggle value
to desired
setting.
• Press and hold
F4 key until
cursor stops
flashing.
MISC FUNCTIONS
Misc. Functions
Menu
- Date Time
- Status
- Run Time
- Program
Version
- Cargo Data
Misc. Functions
Submenu
• Current function setting
appears in display.
• Press F3 key to scroll to
desired function.
• Press F4 key to
change a setting.
• Type new value; or
press F3 key to
toggle value
to desired setting.
• Press and hold F4
key until cursor
stops flashing.
COMMANDS
To Activate a
Command
• Press F4 to start a:
- PTI (Pretrip) Test
- Function Test
Commands Manual
Function Test
Submenu
• First Component
Test appears in
display:
• Press F2 or F3 key
to scroll to the
desired component:
- Condensor
- Sensor Check Low
- Sensor Check
- Heat
- AFAM Close
- AFAM Open
- Evap. Low
- Evap. High
- Dehumidity
Valve
- Injection
Valve
- Digital Valve
- Compressor
• Press F4 key to
start and stop test
(toggle component
display between
ON and OFF).
• More than
one component can
be turned ON at a
time to perform a
functional test of
the unit.
Power Management
Submenu
• Current Power Limit and
Power Time appear in
display.
• Press F3 key to scroll to
desired function.
• Press F4 key.
- Power Limit Press F2 or
F3 key to scroll to new
setting.
- Power Time: Type the new
time in hours.
• Press and hold F4 key
until cursor stops flashing.
MAIN MENU
CONTROLLER MENU GUIDE
- Supply LH
- Supply RH
- Return
- Evaporator
Data Menu
- Condensor
- Suct. Press
- Disch. Press
-Cool Cap.
NOTE: All screens are NOT present on all units. The screen that
display on the controller are determined by the Controller Software
setting and the options installed on the unit.
Text Input: Use F1, F2, F3 and F4 keys to enter text in information screens:
• To enter a number: Press the F1 key and the desired number key.
• To enter 1st letter on a key: Press the F2 key, the desired letter key.
• To enter 2nd letter on a key: Press the F3 key, the desired letter key.
• To enter 3rd letter on a key: Press the F4 key, the desired letter key.
NOTE: When a function key (F1, F3, F3 or F4) is pressed to enter text,
the keypad remains on that “character level: until another function key
is pressed.
To Enter a Controller Menu or Use Special Function Key:
• Press F4 key to directly enter the Data menu.
• Press F2 key to directly enter the Alarms menu.
• Press F3 key to directly enter the Main menu.
• Press SETPOINT key to enter Setpoint menu.
• Press C/F Key to view alternate temperature scale in LED display.
• Press SUP/RET key to view alternate sensor temperature in LED display.
• Press DEFROST key to initiate a manual defrost. Evaporator coil
temperature must be below 10 C (50 F).
To Enter a Submenu, a Command or a New Value in a Text Screen:
• Press F4 key.
To Scroll in a Menu or a Text Line:
• Press F2 key to scroll up or backward.
• Press F3 key to scroll down or forward.
To Exit a Menu or Text Line:
• Press F1 (ESC) key.
Special Function Keys:
• Press C/F key to view alternate temperature scale in LED display.
• Press DEFROST key to initiate a manual defrost. Evaporator coil
temperature must be below 10C.
• Press SUP/RET key to view alternate return/supply-sensor temperature in
LED display.
To Lock a LCD Data Screen Display:
• Each time the “5” key is pressed, the display time of the current LCD
screen increases by 5 mi nutes. Maximum display time is 30 minutes for
data screens and 100 minutes for manual tests. Press F1 (ESC) key to exit
display.