Terasic TR-5 Lite FPGA Скачать руководство пользователя

Страница: 66 / 86

TR5-Lite User Manual

www.terasic.com

June 20, 2018

initial_config initial_config(

.iCLK(iCLK), // system clock 50mhz

.iRST_n(iRST_n), // system reset

.oINITIAL_START(initial_start),

.iINITIAL_ENABLE(1'b1),

);

Changing the setting from ".iINITIAL_ENABLE(1'b1) " to ".iINITIAL_ENABLE(1'b0)" will

disable the initialization function of Si570 Controller.



Design Tools



Quartus II 13.1



Demonstration Source Code



Project directory: TR5_LITE_SI570_Controller



Bit stream used: TR5_LITE_SI570_Controller.sof



Demonstration Batch File : test.bat (For USB-Blaster)/ test_ub2.bat (For USB-Blaster II)



Demo Batch File Folder: TR5_LITE_SI570_Controller \demo_batch

The demo batch file folders include the following files:



Batch File: test.bat (For USB-Blaster)/ test_ub2.bat (For USB-Blaster II)



FPGA Configuration File: TR5_LITE_SI570_CONTROLLER.sof



Demonstration Setup



Make sure Quartus II is installed on your PC.



Connect the USB Blaster cable to the TR5-Lite board and host PC. Install the USB Blaster driver

if necessary.

Содержание TR-5 Lite FPGA























































































Результаты поиска

Содержание TR-5 Lite FPGA

Отзывы:

Похожие инструкции для TR-5 Lite FPGA

Бренды по названию

Популярные бренды

Terasic TR-5 Lite FPGA, Руководство пользователя

Результаты поиска

Содержание TR-5 Lite FPGA

Отзывы:

Похожие инструкции для TR-5 Lite FPGA

Бренды по названию

Популярные бренды