Tennant 8200D Скачать руководство пользователя страница 47

Страница: 47 / 102

OPERATION

8200D 330080 (1--98)

4. Adjust brush pressure for cleaning

application.

Scrub brush pressure: Press and hold the

scrub switch. The brush pressure will scroll

through three settings. The pressure setting

selected when the switch is released will be

the new default brush pressure setting.

The brush pressure can be set into three

different positions. Under normal conditions,

the brush pressure should be set in the

minimum settings (one or two indicators

above switch are lit). Under heavy grime

conditions, the brush pressure should be set

in the maximum setting (three indicators lit).

Travel speed and floor conditions will affect

the scrubbing performance.

5. Press the edge scrub switch (option) if edge

scrubbing is necessary.

6. Press the ES switch (option) if extended

scrubbing is necessary.

NOTE: When using the ES (option), the recovery

tank must be filled with water up to the top of the

ES filter.

NOTE: If you

do not

want to use the ES system,

press the ES switch so the indicator next to the

switch is off.

7. Drive the machine forward and scrub as

required.

WARNING: Flammable materials or

reactive metals can cause explosion or

fire. Do not pick up.

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды