Tennant 8200D Скачать руководство пользователя страница 16

Страница: 16 / 102

OPERATION

8200D 330080 (9--05)

IGNITION SWITCH

The ignition switch starts and stops the engine

with a key.

FOR SAFETY: When starting machine,

keep foot on brake and directional pedal

in neutral.

Preheat the glow plugs: Turn the key all the way

counter-clockwise and hold it there until the glow

plug light goes out.

Start: Turn the key all the way clockwise.

Release the key as soon as the engine starts.

Stop: Turn the key counter-clockwise.

STEERING WHEEL

The steering wheel controls the machine’s

direction. The machine is very responsive to the

steering wheel movements.

Left: Turn the steering wheel to the left.

Right: Turn the steering wheel to the right.

STEERING COLUMN TILT LEVER (OPTION)

The steering column tilt handle controls the angle

of the steering wheel.

Adjust: Pull out the tilt handle, then move the

wheel to the desired position and release the tilt

handle.

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды