Tennant 8200D Скачать руководство пользователя страница 22

Страница: 22 / 102

OPERATION

8200D 330080 (6--04)

ES SWITCH (OPTION)

The ES switch turns the extended scrub system

on and off . When the machine is started, the ES

switch will default to the last setting used.

On: Press the ES switch. The indicator light next

to the switch will illuminate.

Off: Press the ES switch. The indicator light next

to the switch will go out.

NOTE: When the ES switch is on and the water

levels in the tanks are at the proper levels, there

will be a slight delay before the ES pump turns on.

RECOVERY TANK FULL INDICATOR

The recovery tank full indicator will illuminate

when the recovery tank is full of recovered

solution. All scrubbing functions will stop

automatically soon after the recovery tank

becomes full. Drain the recovery tank as soon as

possible after the indicator illuminates. The

indictor light will remain lit until the tank is drained.

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды