Tennant 8200D Скачать руководство пользователя страница 80

Страница: 80 / 102

MAINTENANCE

8200D 330080 (1--98)

REPLACING SIDE BRUSH
The side brush should be replaced when it no

longer sweeps effectively for your application. A

guideline length is when the remaining bristles

measure 50 mm (2 in) in length. You may change

the side brush sooner if you are sweeping light

litter, or wear the bristles shorter if you are

sweeping heavy debris.

1. Empty the debris hopper.

2. Raise the hopper and engage the hopper

support bar.

WARNING: Raised hopper may fall.

Engage hopper support bar.

3. Set the machine parking brake.

4. Stop the engine.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

5. Remove the side brush retaining pin from

the side brush drive shaft by pulling the pin

keeper off the end of the pin.

6. Slide the side brush off the side brush drive

shaft.

NOTE: Remove the drive hub and put it on the

new brush if one is not installed.

7. Slide the new side brush onto the side brush

drive shaft.

8. Insert the side brush retaining pin through

the side brush hub and shaft.

9. Secure the pin by clipping the pin keeper

over the end of the pin.

10. Disengage the hopper support bar and lower

the hopper.

11. Adjust the side brush pattern with the side

brush down pressure knob.

08019

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды