Tennant 8200D Скачать руководство пользователя

Страница: 100 / 102

INDEX

8200D 330080 (6--04)

Engine cover gas spring, 31
Engine oil pressure light, 25
Engine speed switch, 21
Engine water temp light, 25
ES

Clean tanks, 33, 51

Detergent level, 33, 51

ES filter, 80
ES switch (option), 20

Filter, Vacuum fan inlet, 33, 51
Filter shaker switch, 22
Filters

cleaning, hopper, 70–71

ES (Extended Scrub), 80

hopper, dust, 70–71

removing, hopper, 71–72

Fuel filter, 67
Fuel level gauge, 17
Fuse, 28

Grease fittings, rear wheel support, 60

Handle, side sweep brush pressure, 16
Hopper

disengaging hopper support bar, 54–56

dust filter, 70–71

dust filter cleaning, 70–71

dust filter removal, 71–72

engaging hopper support bar, 52–54

lift arm pivots, 61

support bar, 31

Thermo Sentry, 71

Hopper door closed light (option), 27
Hopper door lever, 17
Hopper lever, 16
Hopper temp light -- Thermo Sentry, 26
Horn button, 27
Hourmeter, 17
Hydraulic cooler, Fins, 33, 51
Hydraulic filter bypass light (option), 27

Hydraulics

fluid, 63–65

fluid filter, 62

Fluid level, 33, 51

fluid level, 62

hoses, 64

propelling motor, 64

reservoir, 62

system specifications, 95

Ignition switch, 14
Indicators

charging system light, 25

clogged filter light (option), 26

engine oil pressure light, 25

engine water temp light, 25

hopper door closed light (option), 27

hopper temp light -- Thermo Sentry, 26

hydraulic filter bypass light (option), 27

OK light, 26

recovery tank full, 20

Information

about brushes, 36–38

about scrub head, 72

about scrubbing, 36–38

about sweeping, 36–38

Jack points, 93–95

Knob, main sweep brush pressure, 15

Latches, 31
Leveling rear squeegee, 82–84
Levers

hopper, 16

hopper door, 17

side sweep brush, 16

steering column tilt (option), 14

Lights

charging system, 25

clogged filter (option), 26

engine oil pressure, 25

engine water temperature, 25

hopper door closed (option), 27

hopper temperature -- Thermo Sentry, 26

hydraulic filter bypass (option), 27

OK, 26

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды