Tennant 8200D Скачать руководство пользователя

Страница: 20 / 102

OPERATION

8200D 330080 (1--98)

SCRUB SWITCH

The scrub switch controls the scrubbing

operations. The scrub switch also sets the scrub

brush pressure.

The scrubbing operations include the functions

described below. When the machine is moving

forward, the scrub head lowers and the scrub

brushes activate. The scrub head will move into

the edge scrub position if the edge scrub switch

(option) is pressed. The rear squeegee will lower

and the vacuum fan will start. The solution system

will start, if the solution flow switch is on. Also, the

optional ES system and detergent pump will start

if the switches are on. The engine speed will

change to

fast

Start: Press the scrub switch.

Stop: Press the scrub switch again.

Scrub brush pressure: Press and hold the scrub

switch. The brush pressure will scroll through

three settings. The pressure setting selected

when the switch is released will be the new

default brush pressure setting.

The brush pressure can be set into three different

positions. Under normal conditions, the brush

pressure should be set in the minimum settings

(one or two indicators above switch are lit). Under

heavy grime conditions, the brush pressure

should be set in the maximum setting (three

indicators above switch are lit). Travel speed and

floor conditions will affect the scrubbing

performance.

NOTE: The brush pressure setting, and the

detergent flow rate will default to the last settings

used when the scrubbing operations are started

again.

NOTE: The scrub head will raise when the

directional pedal is in the neutral position. The

rear squeegee will raise when the directional

pedal is in the reverse position.

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды