Tennant 8200D Скачать руководство пользователя

Страница: 87 / 102

MAINTENANCE

8200D 330080 (12--00)

6. Position the retaining band over the

squeegee blade. Latch the retaining band

clamp.

7. Adjust the squeegee blade leveling and

deflection as stated in

LEVELING THE

REAR SQUEEGEE

and

ADJUSTING REAR

SQUEEGEE BLADE DEFLECTION.

SIDE SQUEEGEES

The side squeegees control water spray and

channel water into the path of the rear squeegee.

Check the side squeegees for damage and wear

daily. Replace the side squeegee blades

whenever they become damaged or lose their

shape or resilience. Replace the squeegee

deflectors whenever they become worn.

REPLACING SIDE SQUEEGEE BLADES

1. Raise the scrub head.

2. Turn off the machine and set the machine

parking brake.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

3. Remove the cotter pin, clevis pin, deflector,

and the retainer bracket from the front of the

side squeegee.

4. Pull the squeegee blade off the front of the

squeegee frame.

5. Slide the new squeegee blade onto the

frame.

NOTE: Lubricating the squeegee frame where

the squeegee makes contact will make for easier

squeegee installation.

6. Replace the retainer bracket, deflector,

clevis pin, and cotter pin.

7. Repeat for the side squeegee on the other

side of the scrub head.

05942

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды