Tennant 8200D Скачать руководство пользователя

Страница: 45 / 102

OPERATION

8200D 330080 (1--98)

6. Remove the detergent tank (option) lid. Fill

the tank to just below the top. Be sure to use

only the proper detergent for your scrubbing

application. Put the lid back on the detergent

tank.

WARNING: Flammable materials can

cause an explosion or fire. Do not use

flammable materials in tank(s).

NOTE: Floor conditions, water condition, amount

of soilage, type of soilage, and brush action all

play an important role in determining the type and

concentration of detergent used. For specific

recommendations, contact your TENNANT

representative.

ES mode with auto-fill: Connect the hose

from the water source to the auto-fill

connection on the machine. Turn the ignition

key to the on position and turn on the water

source. The auto-fill will automatically fill the

tanks to the proper level for ES operation

and automatically shut-off.

ES mode

without

auto-fill: Fill the solution

tank to the FULL line.

ES mode

without

auto-fill: Fill the recovery

tank half full of water (to the top of the ES

filter).

NOTE: If you DO NOT want to use the ES

system, DO NOT put water in the recovery tank.

Turn the ES switch OFF.

7. Close the tank cover.

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды