Tennant 8200D Скачать руководство пользователя

Страница: 27 / 102

OPERATION

8200D 330080 (11--98)

CHARGING SYSTEM LIGHT

The charging system light will illuminate when the

alternator is not operating within the normal range.

If the light illuminates stop the machine

immediately, then find the problem and have it

corrected.

ENGINE OIL PRESSURE LIGHT

The engine oil pressure light will illuminate when

the engine oil pressure falls below 40 kPa (5 psi).

In this situation, an alarm will sound until the oil

pressure problem is corrected. If the light

illuminates stop the machine immediately, then

find the problem and have it corrected.

ENGINE WATER TEMPERATURE LIGHT

The engine water temperature light will illuminate

when the temperature of the engine coolant is

more than 107

C (225

F). If the light illuminates

stop the machine immediately, then find the

problem and have it corrected.

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды