background image

MAINTENANCE

8200D 330080 (3--02)

70

DEBRIS HOPPER

HOPPER DUST FILTER

The dust filter filters the air pulled up from the

hopper. The dust filter is equipped with a shaker

to remove the accumulated dust particles. The

dust filter shaker is operated by the filter shaker

switch.

The standard dust filter works well for normal

sweeping applications. The synthetic filter works

well for humid or wet applications.

Shake the dust filter before emptying the hopper

and at the end of every work shift. Check and

clean or replace the dust filter every 100 hours of

operation.

To clean the dust filter, use one of the following

methods:

D

SHAKING -- Press the filter shaker switch.

D

TAPPING -- Tap the filter gently on a flat

surface with the dirty side down. Do not

damage the edges of the filter element or

the filter will not seat properly in the filter

frame.

D

AIR -- Always wear eye protection when

using compressed air. Blow air through the

dust filter opposite the direction of the

arrows. Never use more than 690 kPa

(100 psi) of air pressure and never closer

than 50 mm (2 in) away from the filter. This

may be done with the dust filter in the

machine.

FOR SAFETY: When servicing machine,

wear eye and ear protection when using

pressurized air or water.

D

WATER -- Rinse the synthetic filter with a

low pressure garden hose through the dust

filter opposite the direction of the arrows.

The standard dust filter can also be rinsed,

but the filter will degrade with each rinsing

and should be replaced after rinsing five

times.

NOTE: Be sure the dust filter is dry before

reinstalling it in the machine.

Содержание 8200D







































































































Отзывы: