Tennant 8200D Скачать руководство пользователя

Страница: 33 / 102

OPERATION

8200D 330080 (1--98)

HOPPER SUPPORT BAR

The hopper support bar is located on the

operator’s side of the hopper. The hopper support

bar holds the hopper in the raised position to allow

work under the hopper. DO NOT rely on the

machine hydraulic system to keep the hopper

raised.

WARNING: Raised hopper may fall.

Engage hopper support bar.

ENGINE COVER GAS SPRING

The engine cover gas spring is located

underneath the engine cover. The gas spring

holds the engine cover in the raised position to

allow work on the engine.

To close the engine cover, push the lower portion

of the gas spring in line with the top portion, and

push the engine cover downward.

LATCHES

The solution tank cover and the side and top

engine doors are secured with latches.

Open: Press the raised part of the latch.

Close: Press the flat part of the latch.

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды