Tennant 8200D Скачать руководство пользователя

Страница: 73 / 102

MAINTENANCE

8200D 330080 (6--04)

REMOVING HOPPER DUST FILTER

1. Stop the engine and set the machine parking

brake.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

2. Open the hopper cover.

3. Lift the dust filter element out of the hopper

insert.

4. Clean or discard the dust filter as required.

5. Put the cleaned or new dust filter in the

hopper insert with the arrows pointing up.

6. Close the hopper cover.

THERMO SENTRY

The Thermo Sentry, located inside the

hopper, senses the temperature of the air pulled

up from the hopper. If there is a fire in the hopper,

the Thermo Sentry stops the vacuum fan and cuts

off the air flow.

The Thermo Sentry resets itself automatically

after cooling down.

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды