Tennant 8200D Скачать руководство пользователя страница 17

Страница: 17 / 102

OPERATION

8200D 330080 (1--98)

The main sweep brush lever controls the position

and rotation of the main sweeping brush.

Main brush down and on: Pull the lever back and

to the right, then allow it to move forward into the

main brush down and on

position.

Main brush up and off: Pull the lever back and to

the left into the

main brush up and off

position.

The brush will raise, stop rotating, and the

vacuum fan will shut off automatically.

NOTE: The filter shaker will automatically shake

the filter for 15 seconds each time the main brush

is raised.

MAIN SWEEP BRUSH DOWN PRESSURE

KNOB

The main brush down pressure knob changes the

amount of contact the main brush has with the

surface being swept.

Increase: Turn the main brush down pressure

knob counter--clockwise.

Decrease: Turn the main brush down pressure

knob clockwise.

Содержание 8200D







































































































Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды

Tennant 8200D, Руководство оператора

Результаты поиска

Содержание 8200D

Отзывы:

Похожие инструкции для 8200D

Бренды по названию

Популярные бренды