Tennant 6550D Скачать руководство пользователя страница 84

Страница: 84 / 96

MAINTENANCE

6550D 330330 (5--01)

BRAKES AND TIRES

SERVICE BRAKES

The mechanical service brakes are located on the

front wheels. The brakes are operated by the foot

brake pedal and connecting cables.

Check the brake adjustment every 200 hours of

operation. The brake pedal should not travel more

than 25 mm (1 in) to fully engage the brakes.

PARKING BRAKE

The parking brake is set with the parking brake

lever that activates the service brakes.

Adjust the parking brake whenever it becomes

very easy to set the parking brake, when the

machine rolls after setting the parking brake, and

every 200 hours of operation. The parking brake

may be tightened by turning the knurled knob on

the end of the parking brake clockwise.

TIRES

The standard front machine tires are solid. The

standard rear machine tire is pneumatic.

Check the rear tire pressure every 100 hours of

operation. The proper tire air pressure is

790 + 35 kPa (115 + 5 psi).

REAR WHEEL

Torque the rear wheel nuts in a star pattern twice

to 142 to 157 Nm (105 to 115 ft lb) after the first

50-hours of operation, and every 800 hours there

after.

08053

08028

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды