Tennant 6550D Скачать руководство пользователя страница 23

Страница: 23 / 96

OPERATION

6550D 330330 (5--98)

ENGINE OIL PRESSURE LIGHT

The engine oil pressure light comes on when the

engine oil pressure falls below 35 kPa (5 psi).

Stop operating the machine. Locate the problem

and have it corrected.

CHARGING SYSTEM LIGHT

The charging system light comes on when the

existing voltage potential of the battery is not

within normal range -- 10 to 14 Volts. Stop

operating the machine. Locate the problem and

have it corrected.

HOPPER DOOR LIGHT

The hopper door light comes on when the hopper

door is closed. Make sure the hopper door is open

and the hopper door light is off, before sweeping

with the machine.

CLOGGED FILTER LIGHT

The clogged filter light comes on when the hopper

dust filter is clogged.

To clean the filter, press the filter shaker switch. If

the clogged filter light remains lit, manually clean

the hopper dust filter. See

HOPPER DUST

FILTER

MAINTENANCE.

07758

07757

07763

07762

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды