Tennant 6550D Скачать руководство пользователя страница 81

Страница: 81 / 96

MAINTENANCE

6550D 330330 (5--98)

REAR SKIRTS

The two rear skirts are located on the bottom rear

of the main brush compartment. The vertical skirt

should clear the floor up to 5 mm (0.25 in) in dusty

conditions, and touch the floor otherwise. The

recirculation skirt is self-adjusting.

Check the skirts for wear or damage and

adjustment daily.

NOTE: Rear tire pressure will affect skirt

clearances.

SIDE BRUSH DUST CONTROL SKIRTS

(OPTION)

The side brush dust control skirts wrap around the

side brush and the bottom of the hopper.

Check the side brush dust control skirts for wear

or damage daily.

BRUSH DOOR SEALS

The brush door seals are located on both main

brush doors and on corresponding portions of the

main frame.

Check the seals for wear or damage every

100 hours of operation.

08021

08022

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды