Tennant 6550D Скачать руководство пользователя страница 31

Страница: 31 / 96

OPERATION

6550D 330330 (9--01)

LATCHES

The side doors, rear doors, engine cover, hopper

cover, and cab door are secured with latches.

Open the Main Brush Side Doors: Push down on

the door latch.

Open the Engine Side Door: Pull up on the door

latch.

Open the Grille Doors: Push down on the door

latch.

Open the Engine Cover: Push in on the cover

latch.

Open the Hopper Cover: Push the cover latch to

the right and pull up on the hopper cover.

Open the Cab Door: Pull up on the door handle.

HOPPER SUPPORT BAR

The hopper support bar is located on the

operator’s side of the hopper. The hopper support

bar holds the hopper in the raised position to allow

work under the hopper. DO NOT rely on the

machine hydraulic system to keep the hopper

raised.

WARNING: Raised hopper may fall.

Engage hopper support bar.

08149

07803

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды