Tennant 6550D Скачать руководство пользователя страница 64

Страница: 64 / 96

MAINTENANCE

6550D 330330 (5--98)

HYDRAULICS

HYDRAULIC FLUID RESERVOIR

The reservoir is located in the engine

compartment next to the radiator.

Mounted on top of the reservoir is a filler cap with

a fluid level dipstick. The reservoir also has a

hydraulic breather located next to the filler cap.

Replace the hydraulic breather after every 800

hours of operation.

Check the hydraulic fluid level at operating

temperature every 100 hours of operation. Make

sure the hopper is down when checking hydraulic

fluid level. The end of the dipstick is marked with

FULL and ADD levels to indicate the level of

hydraulic fluid in the reservoir.

Lubricate the filler cap gasket with a film of

hydraulic fluid before putting the cap back on the

reservoir.

ATTENTION! Do not overfill the

hydraulic fluid reservoir or operate the

machine with a low level of hydraulic

fluid in the reservoir. Damage to the

machine hydraulic system may result.

Drain and refill the hydraulic fluid reservoir with

new hydraulic fluid every 800 hours of operation.

The hydraulic fluid filter is located at the bottom of

the engine compartment. Replace the filter

element every 800 hours of operation.

The reservoir has a built-in strainer outlet that

filters hydraulic fluid before it enters the system.

Replace the strainer every 800 hours of operation.

HYDRAULIC FLUID

The quality and condition of the hydraulic fluid

play a very important role in how well the machine

operates. TENNANT’s hydraulic fluid is specially

selected to meet the needs of TENNANT

machines.

08007

07750

08051

Содержание 6550D

































































































Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды

Tennant 6550D, Руководство оператора

Результаты поиска

Содержание 6550D

Отзывы:

Похожие инструкции для 6550D

Бренды по названию

Популярные бренды